• Spotlights

There should be a small white ceramic block on the firewall - this component cuts the battery voltage from 12 to 9 volts for the coil and ignition system. It has 4 wires and is called a ballast resistor. You may need a book with the wiring diagram to be able to test it. You should have battery voltage going in and something like 9 volts coming out. You can also run a wire with a fuse from the battery to the positive side of the coil to check the system. Disconnect the factory wire from the coil first. Jan 27, 2013.

Hi One of the most common problems with washing machines, however, is that they won't spin. Usually this is caused by an issue that easily can be fixed, but other times it can be more serious. In some cases, just the balance of the load can cause the machine not to spin. First open the lid and reposition the clothes. Close the lid and retry. The washer may not spin at all if the tub is unbalanced. Examine the lid switch for wear.

Replace a worn lid switch by first using a screwdriver to remove the top of the machine. Remove the cabinet holding the old switch in place by unscrewing the two console screws, tilting the console back, removing cabinet clips, and unlocking the lid switch block. Unscrew the mounting screws, and disconnect the ground wires before removing the old switch. Insert the new switch in it's place. Look for excessive glazing or cracks on the sides of the belt. If these signs appear, remove the old belt by tipping the washing machine over on it's side, and unscrew the clamps securing the pump coupling with a screwdriver. Place the new belt over the transmission pulley, and then over the motor pulley's nearest edge, slowly turning the motor pulley to pull the belt around and into the pulley.

Replace the washer's motor by firmly grasping on the metal slip-on connectors holding the wires in place, allowing you to pull the connectors apart. Use a screwdriver to unscrew all of the screws holding the motor in place, and remove the old motor. Insert the new motor in its place.

Dorcy Lights & Flashlights See All. DORCY 3D LED WIRELESS MOTION SENSOR FLOOD LITE. Dorcy 41-1068 3-AA Battery Operated Indoor. Dorcy Flashlight How To Install Batteries In Fire. Of course by now you know that I like redundancy with my preps. Dorcy LED Wireless Motion Sensor Flood Lite. Dorcy FAQ's ( Frequently asked questions ) can be a great resource for questions. The battery holder is broken in my LED flashlight. What do I do?

Secure the new motor to the machine with screws, and reconnect the motor's wiring harness. Replace the washer's pump by removing the service panel on the back of the machine with a screwdriver and disconnecting the washing machine drain line and the rubber pump outlet hose. Remove the fasteners holding the pump to the bottom of the machine, along with the drive belt from the pulley below the pump. Replace the old pump with a new one, and reinstall the drive belt back on the pulley, reinsert the fasteners and reconnect the rubber pump inlet and discharge lines. Also check this link to get a detailed idea related to your issue:- Please get back to us if you have further query or else please accept the solution. Sep 03, 2011. Some P touch series had trouble with the lid not closing, or seating, and some may not have the batteries inserted the way that is logical.

Check the battery polarity one by one and make sure that they are going in in the right position and order. Then make sure the tape is in right and seated and that the lid closes. If all these don' t solve it take it back and get a new one as there is not a reset that I am aware of. Check your specific model for a small reset round hole on the bottom just in case and try the manual. Jun 13, 2011. Hi Open the lid and reposition the clothes. Close the lid and retry.

The washer may not spin at all if the tub is unbalanced. Examine the lid switch for wear. Replace a worn lid switch by first using a screwdriver to remove the top of the machine. Remove the cabinet holding the old switch in place by unscrewing the two console screws, tilting the console back, removing cabinet clips, and unlocking the lid switch block. Unscrew the mounting screws, and disconnect the ground wires before removing the old switch. Insert the new switch in it's place.

Look for excessive glazing or cracks on the sides of the belt. If these signs appear, remove the old belt by tipping the washing machine over on it's side, and unscrew the clamps securing the pump coupling with a screwdriver. Place the new belt over the transmission pulley, and then over the motor pulley's nearest edge, slowly turning the motor pulley to pull the belt around and into the pulley. Replace the washer's motor by firmly grasping on the metal slip-on connectors holding the wires in place, allowing you to pull the connectors apart. Use a screwdriver to unscrew all of the screws holding the motor in place, and remove the old motor. Insert the new motor in its place. Secure the new motor to the machine with screws, and reconnect the motor's wiring harness.

Replace the washer's pump by removing the service panel on the back of the machine with a screwdriver and disconnecting the washing machine drain line and the rubber pump outlet hose. Remove the fasteners holding the pump to the bottom of the machine, along with the drive belt from the pulley below the pump. Replace the old pump with a new one, and reinstall the drive belt back on the pulley, reinsert the fasteners and reconnect the rubber pump inlet and discharge lines. However there are various reasons as to why a washing machine won't spin.

Also check this bellow link to troubleshoot your issue:- May 03, 2011. Do not use batteries with different amp-hour (Ah) capacities.

Spotlights

Do not mix old and new batteries. Always replace both batteries at the same time.

Battery posts, terminals, and related accessories contain lead and lead compounds. Wear goggles and gloves when handling batteries and wash hands after handling. Always use two batteries of the exact same type, chemistry, and amp-hour (Ah) capacity. Use 12 Volt deep cycle batteries. 1.Remove the battery pack from the Travel Scooter. 2.Carefully turn the pack upside down.

3.Remove the eight (8) screws from the perimeter of the battery pack. 4.Carefully turn the pack right side up and remove the lid. 5.Disconnect the black (-) and red (+) battery cables from the battery terminals. 6.Remove the old battery. 7.Place a new battery in the battery pack. 8.Connect the red battery cable to the positive (+) battery terminal.

9.Connect the black battery cable to the negative (-) battery terminal. 10.Position the lid back onto the battery pack ensuring all wires are inside the pack so they don’t become pinched. 11.Carefully turn the pack upside down. 12.Reinstall all screws and tighten. 13.Charge the new batteries for 8-14 hrs before the first use.

I hope this helps and good luck! Feb 24, 2010. Free download program best the back horn rar extractor.

Hello, Try this procedure: 1. Open printer lid so cartridges move to center of carriage. Lift clamp and remove black or color cartridge from the holder. Place cartridge on table with copper contact strip facing you. Carefully place a strip of clear plastic tape over the four contacts on the upper left corner of the cartridge. Reinstall cartridge in printer and close lid.

Wait until cartridge returns to parking position. Open lid and remove cartridge again. Remove tape from left side and place tape over four contacts at upper right corner of cartridge. Reinstall cartridge in printer and close lid.

Wait until cartridge returns to parking position again. Open lid again, remove cartridge, remove tape. Reinstall cartridge and close lid. Printer will now recalibrate. Once the process is complete the ink level meter should be reading full again. I hope this helps, if so please rate our solution. Buddy Corporate Computer www.ccl-la.com Dec 22, 2009.